Menu
Your Cart

SHARP V-1 12" X 58" DIGITAL VARIABLE SPEED VERTICAL MILLING MACHINE

SHIPPING & DELIVERY
Call us now
Ask a question
SHARP V-1 12" X 58" DIGITAL VARIABLE SPEED VERTICAL MILLING MACHINE
SHARP V-1 12" X 58" DIGITAL VARIABLE SPEED VERTICAL MILLING MACHINE
Based on 0 reviews. - Write a review
$40,990.00
  • Stock: In Stock
  • Model: V-1
  • Weight: 4,500.00lb
  • Dimensions:
  • 75.00in x 83.00in x 100.00in
  • SKU: V-1
SHARP SHARP
Add to Cart
Buy Now Question
Add to Wish List Compare this Product
  • ISO 9002 certified quality to industry standards
  • YASKAWA® inverter drive system with large LED RPM display and lower voltage control
  • Rigid 5 HP inverter driven Digital Variable Speed (DVS) spindle is equipped with 4-1/8" diameter oversize quill for heavy milling jobs
  • Centralized pendant control with low voltage electrical controls and E-stop
  • Highest grade Meehanite® casting with full ribbed to dampen vibration
  • A pair of precision ABEC-7 angular contact bearings to support spindle
  • High out-put double fans keep head and motor cool, to run jobs for extended periods without damaging the motor, belts and bearings
  • The spindle is ground and chromed to fit the housing to insure runout of .0002" T.I.R.
  • Motor shaft and variable speed drive pulleys are dynamically balanced, then chromed for flawless fit, ground ribs on inside diameter, for smooth speed changes
  • Motor shaft has an oil channel in the center that is fed by grease fitting on the lower end, to keep variable speed drive pulley moving smoothing on the shaft
  • Use a roller bearing for lower support of the shaft to ensure proper loading, support and alignment to prevent the shaft from being distorted by the tension of the belt, for quiet, accurate operation at any speed
  • Knuckle joint using bolts and circular T-slot design, allowing head to swivel left and right, up and down for better accuracy and performance
  • Table and saddle backlash is controlled by double nut design, keeps leadscrew in contact with bronze nuts all times to keep backlash at .0008" within 20"
  • Table and saddle are mounted with thrust bearings that preloaded the feed screw, eliminating end-play for precisely controlled lateral movement
  • Hardened and ground box ways on column and saddle for maximum rigidity
  • Hand scraped saddle and knee for better oil retention to avoid chips and dirt embed in the knee and damage the sliding surface
  • Metal casting tray at each end of table
  • Extra wide saddle for full support of table
  • Power feed table and saddle, motorized rapid knee axis for easy positioning
  • Automatic lubrication system delivers oil to all the sliding ways through well placed lubricating channels, The system is designed with back flow valves to prevent oil from flowing back towards the reservoir
  • Complete coolant system, including nozzle, connecting hoses and chip tray
  • Machine runs 220V/3 or 1 Phase/60 Hz., prewired 220V/3 Phase
Table Size (W x L/In.) 12 x 58
Spindle Taper NMTB-40
Diameter of Quill (In.) 4-1/8
Number of Spindle Speeds Digital Variable Speed
Range of Spindle Speeds (RPM) 70 - 4,000
Quill Down Feed Rates (IPR) .0015 - .003 - .006
Spindle Travel (In.) 5
Head Movement (Right or Left | Front or Back) 90° | 45°
Maximum Distance Spindle Nose to Table (In.) 18
Minimum Distance Spindle Nose to Table (In.) 2
Maximum Distance Spindle Center to Column (In.) 24
Minimum Distance Spindle Center to Column (In.) 6
Maximum Table Longitudinal Travel (In.) 40
Maximum Table Cross Travel (In.) 16
Maximum Knee Travel (In.) 16
Maximum Ram Travel (In.) 17-3/4
Width of Saddle (In.) 26
Table T-Slots Number and Size (W x D/In.) 3 | 5/8 x 2-1/2

Main Motor (HP)		 5,
220V/3 or 1 Phase/60 Hz.,
Prewired 220V/3 Phase 
Table and Saddle Power Feed Motor (HP) 1/4
Knee Rapid Motor (HP) 1-1/2
Floor Space Dimensions (W x D x H/In.) 83 x 75 x 100
Machine Weight (Lbs.) 4,500
Design and specifications are subject to change without notice.
  • Table & Saddle Power Feeds and Built-In Knee Rapid Feed
  • Automatic Lubrication System
  • Draw Bar
  • Front and Rear Rubber Way Covers
  • Halogen Work Light
  • Complete Coolant System, Including Nozzle, Connecting Hoses and Chip Tray
  • Toolbox with Tools
  • 440V/3 Phase/60 Hz. Transformer
  • ACU-RITE 203S 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • ACU-RITE 203S 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • ACU-RITE 203S 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • FAGOR 20I 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • FAGOR 30I 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • FAGOR 30I 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • MAXI TORQUE-RITE Air Operated Power Drawbar System with Installation
  • 4" Riser Block with Installation
  • 6" Riser Block with Installation
  • 8" Riser Block with Installation
  • Right Angle Milling Attachment with Arbor
  • Horizontal/Vertical Rotary Table
  • KURT 6" Milling Machine Vise with Swivel Base
  • Clamping Kit
  • Drill Chuck and Arbor
  • ER Collet Chuck System Complete Kit
  • UL Components Upgrade with Electrical Box - Factory Installed
  • UL Compliance Certificate - State of California
  • CE Mark
This website uses cookies to ensure you get the best experience on our website. This use may include analytics, personalization and ads. Learn More